Portable RAP Plant

CARRIER CHASSIS

• HD wide flange structural beams
• W beam block legs placed accordingly along the frame
  • Four (4) “sets” (8 legs total) of Holland Mark V landing gear
• Screen Box and Feed Hopper Access
  • Two (2) access ladders
  • All hand railing includes necessary kick plates
  • Walkway surfaces covered with diamond grip checker platehoppers and chutes
• 3/8” Bolster king pin. All brakes, tail & marker lights, flashing amber led strobe lights, reflectors and mud flaps as required. Over-dimensional flag pipes in all 4 corners fitted with corresponding flag
• Tandom axle suspension
  • Eight (8) 11r22.5.5 tires on steel budd wheels
  • 25,000 Lb rated x 77.5” Track axle assemblies fitted with service pots (to assist with pit portability) and automatic slack adjusters
• Replaceable 60 durometer skirt board rubber including clamp bars where required
• Grease package consisting of one (1) – two (2) locations on the chassis where head and tail pulley
• All necessary guards (frame, v-belt and pinch area)
• Colors are Superior Industries styling
• Hydraulic package consists of the following:
  • Supply and installation of 12 vdc electric over hydraulic power unit. Power unit fitted with 10’ – 12’ long “booster cables” to allow hook-up to customer supplied 12vdc. C/W hd “cat style” master switch to easily allow turning “on & off”. Master switch eliminates the “sparking” that typically occurs when hooking up booster cables.
  • Necessary hydraulic cylinders to hydraulic fold screen discharge conveyor for operation and transportation requirements.
  • All hydraulic valves, hoses, and fittings. Unit comes completely plumbed, filled with oil, tested and ready for immediate operation

3X8 2 DECK SCREEN

• Shim adjustable counterweights (for amplitude efficiency)
• Screen box sub-frame
• Screen is installed to operate in inclined position
• 7.5 HP electric motor

8’ X 16 FEED HOPPER

• Feed hopper fitted with a manual tilt grizzly
  • Hinges provided on both sides
  • Grizzly adjustable at 2” increments to 4”, 6” or 8” opening. Standard factory setting of 6” between bars
  • Bars are of a triangular construction, 3/4” x 4”flat bars on top with 3/8” x 4” flat bar sides
• Re-inforced sides and all necessary leg supports where required.
• Exterior sides of feed hopper fitted with “removable panels”
  • These panels act as “guarding” to prevent access to conveyor and also assist in keeping debris or foreign material from entering the area during operation
• Manual adjustable gates
• Manual folding end wings for additional capacity

CONVEYORS

• 36” belt under hopper
• 24” screen feed conveyor
• 24” screen discharge conveyor

OPTIONS

• Electrical package
  • Cable sets four (4) motors
  • Electrical junction box for motor feed cables
  • Electrical junction box for multi-conductor wire/cable
  • Additional receptacle installed in empty cavity in receptacle housing
  • Speed encoder for 36” under hopper conveyor
  • Multipin connections for encoder and torspec control system
  • Connection for torspec control card to plc and existing control system
  • Belt scale system wiring
  • Complete drawing package
  • Labor and commissioning
  • PLC programming
• Hydraulic “lift-only” leveling jacks package
  • Supply and installation of four (4) 6” x 22” stroke hydraulic leveling cylinders. Cylinders C/W a ¾” thick “oscillating” base plate measuring approximately 10” x 10”. The swivel pad design helps with uneven footings.
  • All hydraulic valves, hoses, and fittings. Unit comes completely plumbed, filled with oil, tested and ready for immediate operation
• Electric bin vibrator package
  • One (1) electric vibrator unit supplied and installed on 8’ x 16’ hopper